Product Introduction
The AH2 handheld drone detection device is powerful and widely applicable. It is mainly used for detecting racing drones, DIY drones, and drones from brands such as DJI and Autel. It is also suitable for various drones that comply with GB42590-2023, ASD-STAN prEN 4709-002, and ASTM F3411 standards.
Multi-mode Detection: Employs a combined spectrum and data packet analysis detection method to ensure comprehensive and accurate detection.
Product Features
1,Rich Information Capture: For drones supporting GB42590-2023, ASD-STAN prEN 4709-002, and ASTM F3411 standards, it can acquire rich information, including the latitude and longitude of the aircraft and pilot, device ID number, distance, altitude, and aircraft bearing.
2,Ultra-Wide Band Coverage: Fully covers the entire frequency band of simulated video transmission FPV drones, leaving no "suspicious elements" undetected.
3,Precise Frequency Band Detection: Capable of accurately detecting specific frequency bands for FPV video transmission.
4,Safe, Offline Detection: The detection process does not rely on external infrastructure, ensuring the independence and security of the equipment.
5,Multiple Alarm Methods: Provides three alarm methods simultaneously: text display, sound, and vibration, promptly alerting the user.
6,Long Battery Life: Built-in 8Ah high-capacity battery allows for continuous and stable operation for 5-6 hours, meeting the needs of extended operation.
7,Convenient user experience: The device is designed to be small and lightweight, ready to use as soon as it is turned on. It is easy to operate and carry, and can easily handle both outdoor inspections and emergency response.
Product Parameters
|
Item |
Parameters |
|
Detection frequency band |
300M-6000MHz |
|
Detection distance |
0.5-3km (depending on the surrounding electromagnetic environment) |
|
Alarm methods |
Text, sound, distance, color, etc. |
|
Detection methods |
Spectrum analysis + over-the-air packet capture + data analysis |
|
Power supply |
Built-in battery, support working 5-6 hours |
|
Product Dimensions |
≤152x 72x 30mm(Without antenna) |
|
Weight |
320g |
|
Operating temperature |
-30°∽+50°C |
|
Working |
Automatic detection upon power-on |
Operating Procedures
This device is very easy to use; it starts working as soon as it's powered on. Please follow these steps:
1,Inspection: Before powering on, check if the device has been stored unused for a long time and confirm the battery capacity.
2, Antenna Installation: There are two antenna ports on the top of the device, marked with "L" and "H". Connect the antenna marked "L" to the "L" antenna port and the antenna marked "H" to the "H" antenna port, and tighten them securely. "L" is for low-frequency antennas, and "H" is for high-frequency antennas.
3,Power on: Press and hold the power button for about 3 seconds. The screen will light up and enter the satellite search and detection state. Depending on the quality of the surrounding navigation signals, wait 1-2 minutes until the satellite icon turns green, indicating that the device has successfully located the device.
The detection display is shown in the image below:
When a drone is detected, if it is an FPV drone, it will display the drone type,frequency band, and signal strength;
If it is a RID drone, it will display the distance between the drone and the device, update time, model, drone ID, instantaneous speed, true altitude,azimuth angle between the drone and the device (North is 0, increasing clockwise), and distance between the takeoff point (pilot) and the device.
Historical data query:
The vibration button is a multi-function button. A short press will enter thehistorical data query interface. After entering the historical data interface, pressthe volume + or volume - button to switch between up and down pages for easyviewing. A maximum of 30 historical data entries can be queried.
Hot Tags: ah2 drone detection equipment, China, suppliers, manufacturers, factory, customized, wholesale, discount, pricelist, quotation
